![]() Be careful not to damage or cut the fan wires.īend the two legs of the cotter pin to ensure that the connector pin doesn’t slip out. ![]() Insert the connector pin through the holes, and secure with a cotter pin. Insert the downrod into the collar yoke and rotate until the holes match. Step 3: Inserting Downrod into Collar Yoke Take extra care not to pull on the electrical wires. Thread the lead wires from the motor (black, white and blue) through both the canopy and downrod. Install the downrod into the mount with the ball end toward the ceiling. (Downrod installations are used for both standard and angled applications.) Installing a Downrod for Your FanĪ downrod allows the fan to be hung from high ceilings and are available in various lengths to accommodate your home’s architecture. ![]() Step 5: Decide on Close Mount or Downrod InstallationĪt this point, if you have a fan with a three-position mount, you’ll need to decide whether to use a close-mount (flushmount) or downrod installation. Pull the electrical wires through the center hole of the mounting bracket. The hook will support the weight of the fan motor housing for a hands-free wiring installation. If the fan comes with a J-hook, install the mounting bracket with the J-hook toward the floor. Secure the mounting bracket to the ceiling electrical box with mounting screws and lock washers. Step 3: Securing Mounting Bracket to Ceiling Electrical Box Remove the mounting bracket from the fan canopy. These screws will be used later to secure the blade arms to the motor. Step 1: Remove Your Harbor Breeze Fan Motor Screws Here are the steps on how to install it correctly: Installing the Mounting Bracket for Your Harbor Breeze Ceiling FanĪ properly installed mounting bracket ensures a safe and efficient ceiling fan. Secure the box to the bracket with a U-bolt. These may be positioned either from the attic or from below the ceiling, through the rough opening. Otherwise, install an expandable metal ceiling-fan hanger bar. If there isn’t a 2-by-4 wood brace between the joists but you have access to the framing through the attic, add a brace. Secure the new box to a brace between ceiling joists. If you require any additional parts or replacement parts then please check our article: Harbor Breeze Replacement Parts: Ceiling Fans Remotes & More Use the installation hardware recommended by the junction box manufacturer.įans over 35 pounds, with or without accessories, require additional support independent of the outlet box. The box and its support must be able to support the moving weight of the fan. Replace the old box with one labelled as approved for ceiling fans or ceiling-suspended paddle fan installation. Your Harbor Breeze Ceiling Fans blades must be mounted at least 7 feet above the floor.įor maximum efficiency, they shouldn’t have any obstruction within 24 inches of the blade tips.Īn appropriate junction or outlet box securely attached to the building structure is required. Options for Mounting Your Harbor Breeze Ceiling Fan Refer to the manufacturer’s instructions for safety, warning and caution information. To reduce the risk of fire or electric shock, don’t use the fan with any solid-state speed-control device or variable speed switch unless it’s specifically designed for use with a ceiling fan.ĭon’t mount the ceiling fan to a plastic electrical box. Do not use bulbs with wattage greater than specified for this fixture (if applicable).If in doubt, consult a qualified electrician.Check with local authorities to see if a permit is required. All electrical connections must be in agreement with local codes.Place the wall switch in the OFF position.Test the wires to ensure the power is OFF.Turn OFF electricity at the main fuse box (or circuit box) that controls the power to the fixture or the room you’re working on.All wiring must conform to local and national codes. If additional wiring must be done to install your fan and you aren’t familiar with wiring, consult a professional electrician. Installation isn’t difficult and only requires that you pay attention to the instructions. Since ceiling fans are usually used to replace existing light fixtures, the wiring to the fan should already be complete. To ensure that your fan is securely mounted to the ceiling and for your safety during installation, read all of the instructions packed with your fan. ![]() Prepare to Install Your Harbor Breeze Ceiling Fan Use a 52-inch diameter ceiling fan if the largest room dimension is 15 feet to 18 feet.Use a 42-inch diameter ceiling fan if the largest room dimension is 12 feet to 15 feet.Use a 36-inch diameter ceiling fan if the largest room dimension is 12 feet or less.As a rule of thumb you should consider the following size ceiling fan depending on room size:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |